Understanding Stabilization in Nanoporous Intermetallic Alloy Anodes for Li-Ion Batteries Using Operando Transmission X-ray Microscopy.

Tin-based alloying anodes are exciting due to their high energy density. Unfortunately, these materials pulverize after repetitive cycling due to the large volume expansion during lithiation and delithiation; both nanostructuring and intermetallic formation can help alleviate this structural damage. Here, these ideas are combined in nanoporous antimony-tin (NP-SbSn) powders, synthesized by a simple and scalable selective-etching method. The NP-SbSn exhibits bimodal porosity that facilitates electrolyte diffusion; those void spaces, combined with the presence of two metals that alloy with lithium at different potentials, further provide a buffer against volume change. This stabilizes the structure to give NP-SbSn good cycle life (595 mAh/g after 100 cycles with 93% capacity retention). Operando transmission X-ray microscopy (TXM) showed that during cycling NP-SbSn expands by only 60% in area and then contracts back nearly to its original size with no physical disintegration. The pores shrink during lithiation as the pore walls expand into the pore space and then relax back to their initial size during delithiation with almost no degradation. Importantly, the pores remained open even in the fully lithiated state, and structures are in good physical condition after the 36th cycle. The results of this work should thus be useful for designing nanoscale structures in alloying anodes.

Fast-Charging Cathodes from Polymer-Templated Mesoporous LiVPO4F.

Fast-charging cathodes with high operating voltages are critical to the development of high energy and power density lithium-ion batteries. One route to fast-charging battery materials is through the formation of nanoporous networks, but these methods are often limited by the high calcination temperatures required for synthesis. Here, we report the synthesis of carbon-coated nanoporous LiVPO4F with excellent rate capabilities that can be stably cycled up to 4.6 V in standard LiPF6 electrolytes. During charge and discharge at 30C, 110 mAh/g (70% of theoretical capacity) was obtained, and only 9% of capacity was lost after 2000 cycles at 20C. These materials also showed excellent stability, with little self-discharge, an open-circuit voltage of 4.2 V, and a discharge capacity of 139 mAh/g obtained after holding for 12 h. Rate capabilities were further demonstrated in a proof-of-concept full cell made with a nanostructured Nb2O5. These devices were able to deliver 200 mAh/g at 1C and 100 mAh/g at 30C. Finally, operando X-ray diffraction and electrochemical kinetics were further used to provide insight into the nature of fast charging in these materials.

Suppression of Electrochemically Driven Phase Transitions in Nanostructured MoS2 Pseudocapacitors Probed Using Operando X-ray Diffraction.

Pseudocapacitors with nondiffusion-limited charge storage mechanisms allow for fast kinetics that exceed conventional battery materials. It has been demonstrated that nanostructuring conventional battery materials can induce pseudocapacitive behavior. In our previous study, we found that assemblies of metallic 1T MoS2 nanocrystals show faster charge storage compared to the bulk material. Quantitative electrochemistry demonstrated that the current response is capacitive. In this work, we perform a series of operando X-ray diffraction studies upon electrochemical cycling to show that the high capacitive response of metallic 1T MoS2 nanocrystals is due to suppression of the standard first-order phase transition. In bulk MoS2, a phase transition between 1T and triclinic phases (Li xMoS2) is observed during lithiation and delithiation in both the galvanostatic traces (as distinctive plateaus) and the X-ray diffraction patterns with the appearance of the additional peaks. MoS2 nanocrystal assemblies, on the other hand, show none of these features. We hypothesize that the reduced MoS2 crystallite size suppresses the first-order phase transition and gives rise to solid solution-like behavior, potentially due to the unfavorable formation of nucleation sites in confined spaces. Overall, we find that nanostructuring MoS2 suppresses the 1T-triclinic phase transition and shortens Li-ion diffusion path lengths, allowing MoS2 nanocrystal assemblies to behave as nearly ideal pseudocapacitors.

A Metal-Organic Framework with Tetrahedral Aluminate Sites as a Single-Ion Li+ Solid Electrolyte.

We demonstrate the synthesis of the first anionic aluminum metal-organic framework (MOFs) constructed from tetrahedral AlO4 sites. Al-Td-MOF-1 was obtained in a simple two-step synthesis by condensation of 1,4-dihydroxybenzene and lithium aluminum hydride into an amorphous aluminate framework before applying a solvothermal treatment under basic conditions to obtain the crystalline Al-Td-MOF-1 with a chemical composition of Li[Al(C6 H4 O2 )2 ]. The overall Al-Td-MOF-1 structure consists of one-dimensional chains of alternating edge-sharing AlO4 and LiO4 tetrahedral sites describing unidirectional pore channels with a square window aperture of ≈5×5 Å2 , best described topologically as a uninodal 6-coordinated snp rod net. Al-Td-MOF-1 features the highest Li+ loading reported to date for a MOF (2.50 wt %) and proved to be an effective single-ion solid electrolyte. An ionic conductivity of 5.7×10-5  S cm-1 was measured for Al-Td-MOF-1 and the beneficial contribution of crystallinity was evidenced by an 8-fold increase in conductivity between the disordered and crystalline material.

Tuning Porosity and Surface Area in Mesoporous Silicon for Application in Li-Ion Battery Electrodes.

This work aims to improve the poor cycle lifetime of silicon-based anodes for Li-ion batteries by tuning microstructural parameters such as pore size, pore volume, and specific surface area in chemically synthesized mesoporous silicon. Here we have specifically produced two different mesoporous silicon samples from the magnesiothermic reduction of ordered mesoporous silica in either argon or forming gas. In situ X-ray diffraction studies indicate that samples made in Ar proceed through a Mg2Si intermediate, and this results in samples with larger pores (diameter ≈ 90 nm), modest total porosity (34%), and modest specific surface area (50 m2 g-1). Reduction in forming gas, by contrast, results in direct conversion of silica to silicon, and this produces samples with smaller pores (diameter ≈ 40 nm), higher porosity (41%), and a larger specific surface area (70 m2 g-1). The material with smaller pores outperforms the one with larger pores, delivering a capacity of 1121 mAh g-1 at 10 A g-1 and retains 1292 mAh g-1 at 5 A g-1 after 500 cycles. For comparison, the sample with larger pores delivers a capacity of 731 mAh g-1 at 10 A g-1 and retains 845 mAh g-1 at 5 A g-1 after 500 cycles. The dependence of capacity retention and charge storage kinetics on the nanoscale architecture clearly suggests that these microstructural parameters significantly impact the performance of mesoporous alloy type anodes. Our work is therefore expected to contribute to the design and synthesis of optimal mesoporous architectures for advanced Li-ion battery anodes.

Using X-ray Microscopy To Understand How Nanoporous Materials Can Be Used To Reduce the Large Volume Change in Alloy Anodes.

Tin metal is an attractive negative electrode material to replace graphite in Li-ion batteries due to its high energy density. However, tin undergoes a large volume change upon alloying with Li, which pulverizes the particles, and ultimately leads to short cycling lifetimes. Nevertheless, nanoporous materials have been shown to extend battery life well past what is observed in nonporous material. Despite the exciting potential of porous alloying anodes to significantly increase the energy density in Li-ion batteries, the fundamental physics of how nanoscale architectures accommodate the electrochemically induced volume changes are poorly understood. Here, operando transmission X-ray microscopy has been used to develop an understanding of the mechanisms that govern the enhanced cycling stability in nanoporous tin. We found that in comparison to dense tin, nanoporous tin undergoes a 6-fold smaller areal expansion after lithiation, as a result of the internal porosity and unique nanoscale architecture. The expansion is also more gradual in nanoporous tin compared to the dense material. The nanoscale resolution of the microscope used in this study is ∼30 nm, which allowed us to directly observe the pore structure during lithiation and delithiation. We found that nanoporous tin remains porous during the first insertion and desinsertion cycle. This observation is key, as fully closed pores could lead to mechanical instability, electrolyte inaccessibility, and short lifetimes. While tin was chosen for this study because of its high X-ray contrast, the results of this work should be general to other alloy-type systems, such as Si, that also suffer from volume change based cycling degradation.